HST fire security equipment : Security Solution New Burglar and Fire Alarm Systems, Residential security commercial security alarm device

security sensor/aspirating smoke detector-1.jpg

Aspirating Smoke Detector Suction-type Fire Detection

ASD-TC5801 warehouses, offices, production sites, airports large space fire security Suction-type Smoke Detector. High precise pipeline sampling and high sensitive suction Operating environment: clean, large places, or places with hightemperature, high-humidity or strong electromagnetic radiation Application places: warehouses, offices, production sites, airports, factories, historical buildings, clean rooms, EDP rooms, communication exchange rooms, shops, cinemas, leisure centers, churches, libraries, hotels, hospitals, electric and nuclear power plants, storerooms, subways and etc. Wall-mounted structure Technical Specifications Operating voltage: Bus voltage:24V, range allowed: 16V～28V Power: DC24V, range allowed:DC20V～DC28V Operating current: Bus: Standby current: ≤0.6mA, Alarm current: ≤0.6mA Relay output: 1A/24VDC, 1A/120VAC Networking mode: Loop communication, RS-485, CAN bus loop communication Information storage capacity: Fire log: 1000 items, fault log: 1000 items and disable log: 1000 items Max sampling length of single tube: 100m Number of sampling loop: 1 Material of enclosure: Metal Ingress protection rating: IP30 Dimensions (L×W×H): 290mm×125mm×350mm (width not conclude the size of inlet and outlet pipe) Operating environment: Temperature:-10℃～+55℃ Relative humidity:10%～95%, non-condensing Standard: GB 15631-2008

$690.00 $590.00
Save: 14% off

Add to Cart

Conventional Beam Detector non-addressable infrared smoke sensor

Conventional Beam Detector (hereinafter called the detector) is a non-addressable infrared beam smoke detector, which must be used together with a reflector. The number of reflector(s) to be used (one or four) depends on the distance from the detector. With excellent built-in microprocessor, the detector has strong ability of analysis and judgment. The detector can automatically carry out system adjustment, compensation of variation of ambient data, and judgment of fire and fault through fixed algorithm, and indicate these states by LED and signal output terminals. With new and reasonable design, attractive appearance, flexible adjustment and alignment method it’s easy to install and adjust. The sensitivity of the detector can be set through hand held programmer in field, decreasing the demand for cleanliness of field conditions, and enlarging application areas. The detector is applicable to historical buildings, warehouses, large storages, shopping malls, leisure centers, exhibition halls, hotel lobbies, printing houses, clothing factories, museums and prisons etc, as well as places where slight smoke particles exist. II Features (1) Wide operating voltage range, big monitoring areas. (2) Combination of the emitting and receiving part makes mounting easy and optical pathway accurate. (3) Built-in microprocessor enables intelligent judgment of fire alarm and fault. (4) The detector can calibrate automatically, which ensures that one person complete adjustment in short time. It’s also convenient to operate. (5) Self-diagnosis function can monitor the inner fault. (6) Automatic compensation for factors weakening received signals, such as dust contamination, positional excursion and ageing transmitter. (7) It has passive output contacts for fire alarm and fault. (8) Two sensitivity levels can be set in field. (9) The detector’s optical pathway is designed with strong anti-interference ability. (10) SMT processing technology. (11) Attractive and decent appearance. III Technical Specifications (1) Power Voltage: 15VDC to 28VDC (2) Power Current: Commission current›20mA Standby current›12mA Alarm current›22mA (3) Fire Alarm and Fault Contact Output: Fire Alarm Relay: Contact capacity 28V/2A, which is normally open in normal state Page 1 HD106 Conventional Beam Detector Installation and Operation Manual and closed in fire alarm state. Fault Relay: Contact capacity 28V/2A, which is normally open in normal state and closed in fault state. (4) Angle of Adjusting: -6~+6 (5) Sensitivity Level: Level 1: High sensitivity. Level 2: Medium sensitivity. (6) Indication of Detector State: Commission: Green LED and Yellow LED are lit or flash in a certain way. See details in Section VI Commission. Normal monitoring state: Red LED flashes periodically. Fire: Red LED constantly illuminates, and Yellow LED turns off. Fire alarm should be cleared through powering up again. Fault: Yellow LED constantly illuminates. The detector clears the fault signal automatically if the condition causing the fault disappears. Optical pathway obscured totally: the detector first gives fault signal and turns on Yellow LED. 20s later, it alarms fire, illuminates Red LED and turns off Yellow LED. Note: In this case, it does not mean there is a fire. After the obscuration is removed, the detector clears fault signal automatically. Fire signal has to be cleared by powering up the detector again. (7) Operating Environment: Temperature: -10?C to +50?C Relative Humidity: 95%, non condensing (8) Monitoring Area: Maximum monitoring area: 1400m 2 Maximum width: 14m (9) Length of Optical Pathway: 8m to 100m (10) Protection Level: Under common environment, ingress protection rating is IP20. Under special environment, ingress protection rating is IP66 through glue-seal treatment. (11) Dimension: length: 206mm width: 95mm thickness: 95mm (12) Material and Color of Enclosure: ABS, gray (13) Weight: 450g (14) Mounting Hole Spacing: Spacing for embedding: 158mm Spacings for surface mounting: 79mm to 96mm

$150.00

Add to Cart

2 fire zone Mini conventional fire alarm control panel

Small business fire security alarm system. CP-1002 Mini size designed conventional fire alarm 2 zone panel is used for family hotel fire security, restaurant fire security, store or shop fire security alarm. Automatic fire alarm system is a device that automatically detects, displays and sends out fire alarm when fire occurs to the protected object. It is widely used in modern factories, material warehouses, high-rise buildings, computing centers and other buildings, to ensure the safety of people's lives and property plays a huge role. The panel range is designed to meet the requirements of EN54 Parts 2 & 4. The panel can be used independently or connect by RS485. Automatic fire alarm system is composed of trigger device, fire alarm device, fire alarm device, power supply and linkage device with other auxiliary control function. Conventional 2-zone multi-wire fire alarm controller, equipped with any 2-wire smoke, temperature, alarm button and alarm bell, sound and light. At the same time can be equipped with security alarm equipment. More fire alarm systems with free technical support at conventional fire alarm Description: 1. The Mini fire alarm control master panel and slave panel each has 2 zones and each zone can equip Max.30 detectors and call points. 2. It should be installed, commissioned and maintained by suitably qualified service personnel with reference to IEE regulations and any statutory requirements. 3. The 2 zones alarm panel has 1 alarm sound output zones (bell zones), which can equip max.16 sounders for total max. 1A/24V power supplied. 4. The panel (master or slaver) has 24V auxiliary power output supply 2A/24V with fire 1, fire 2 relay output and fault relay output. 5. Enclosure supports two 12V, 4Ah backup batteries. 6. It supports detector head removal and easy for repair or maintenance. 7. It has Test/reset, silence alarm and Evacuate button for easy panel operation. 8. It has indicators of zone1 alarm /fault, zone2 alarm /fault, Sound alarm, and sound fault LED. That clearly showed detectors and sound circuit staturs. 9. There is one master fire alarm control panel and it can work with Max.31 same slaver panel. 10. The master fire control panel will communicate slaver panel one by one and fault will be showed if no response is received. 11. Alarm and fault events of panel No. and zone No. will be showed one by one on Master fire control panel. Specification: 1. System Power Supply: Primary AC 120VAC 50/60 Hz / 240VAC 50/60 Hz Power supply rating 2 Amps @ 24VDC Maximum Battery Charging Current 0.98 Amps @ 26VDC Initiating Device Circuits 2 Zones Alarm Zone 2 Normal Initiating Operating Voltage 23VDC, Maximum 26VDC, regulated 2. Standby current: <50mA 3. Alarm current(not include the others): <150mA 4. Detector Voltage (VDC): 24V 5. Number of sensor zones: 2 zones 6. Max. number of detectors per zone: 30 7. Alarm Voltage: 24V Short Circuit Initiating Current (per zone) 35mA Maximum Maximum Initiating Resistance (per zone) 10 ohms Initiating End-of-Line Resistor 4K7 ohms, 1/2W 5% Standby Detector Current (per zone) 4mA maximum Maximum Detector Count (per zone) 30 detectors Initiating Cabling Type 18AWG Twisted Shielded pair (14 – 18 AWG) Detector Base Impedance 430 ohms Notification Appliance Circuits 1 NACs, Special Application Maximum NAC Current Rating 1 Amp maximum per circuit NAC Operating Voltage 26VDC Nominal, 30VDC Maximum NAC End-of-line Resistor 1N4007 Diode FAULT Relay rating 2A & 30VAC, resistive Alarm( Auxiliary ) Relay rating 2A & 30VAC, resistive Master alarm panel Digital & LED display Slave alarm panel LED display only 9. Max. Alarm current per zone: 300mA 10. Max. number of sounders per zone: 16 11. Max. sounder supply current in fire: 1A/24V 12. Fire fault relay contacts loads: 2A/24V 13. Panel weight without battery: 520g 14: Diameter: 108mm*143mm*40mm upc code: 782123753055 ean code: 0782123753055

$98.00

Add to Cart

Extinguishant Control Panel Gas Release fire fighting

4-zones conventional fire alarm fire automatic fighting system. Extinguishant Control Panel CM1004 Technical specification Mains supply 90 to 270VAC, 50Hz/60Hz Mains supply fuse 3Amp ( F3AL250V) Replace only with similar type Power supply rating 3Amps total including battery charge 28V +/- 2V Maximum ripple voltage ≤200 millivolts Battery type Two 12 Volt sealed lead acid in series. 7Ah maximum Battery charge voltage 27.6VDC nominal Battery charge current 0.7Amaximum Current draw in mains fail condition 0.095Amps With buzzer sounding Current draw in second stage alarm 0.235Amps Two zones in fire(470 ohm in circuit) Current draw in post discharge condition 0.310Amps solenoid outputs active Maximum current draw from batteries 3Amps With main power disconnected NAC outputs(sounder & bell circuit) 26 to 28V DC Fused at 500mAwith electronic fuse 1.2Amp total load over all circuits Fault relay contact rating 2A/30VDC maximum for each Volt free changeover contact Fire relay contact rating 2A/30VDC maximum for each Volt free changeover contact First stage contact rating 2A/30VDC maximum for each Volt free changeover contact Second stage contact rating 2A/30VDC maximum for each Volt free changeover contact Extract contact rating 2A/30VDC maximum for each Volt free changeover contact Zone quiescent current 4mA maximum Terminal capacity 0.5mm 2 to 2.5mm 2 solid or stranded wire Number of detectors per zone ≤30 PCS conventional detectors Number of sounders per circuit Dependent on type and current consumption Detection circuit end of line 4K7±5% 1/2 Watt resistor 3K-5.6K 1/2W Monitored input end of line 4K7±5% 1/2 Watt resistor 3K-5.6K 1/2W Sounder circuit end of line 10K±5% 1/2 Watt resistor 6.8K-20K 1/2W Extinguishant output end of line 10K±5% 1/2 Watt resistor 6.8K-20K 1/2W No. of detection circuits Four 21 to 28V DC No. of sounder circuits Four 21 to 28V DC Extinguishant release output 21V to 28V DC. Maximum load 2Amp Extinguishant release delay time Adjustable 0 to 75 seconds 5 second steps SIL,AL, FLT, RST inputs Switched – min resistance 0 ohms, max 1k ohms Detector alarm threshold 270 ohms to 1K ohms Call point alarm threshold 150 ohms to 1K ohms Short circuit threshold 0 ohms to 130 ohms Statusunit/Ancillary board connection Two wire RS485 connection with electronic fuse. Max. of 32 units-RS485 data cable Size 383mm W x 295mm H x 87mm D metal enclosure Weight 5kg

$169.00

Add to Cart

Fire fighting gas extinguish alarm panel 4 zone

The automatic extinguisher control panel is designed in accordance with European standards EN54-2 and EN54-4 Fire Detection and Fire Alarm systems - Control and Indicating Equipment and EN12094-1 Fixed firefighting systems - Components for gas extinguishing systems Part 1: Requirements and test methods for electrical automatic control and delay devices. The control equipment is a combined fire alarm control panel and extinguishing system and has four detection zones, any or all of which are capable of contributing to the extinguisher release decision. Control panels have an integral, mains powered battery charger and power supply designed in accordance with the requirements of EN54-4. Technical specification Table 1 - Electrical specifications ITEM ELECTRICAL RATING COMMENT Size 383 mm W x 295 mm H x 87 mm D metal enclosure Weight 5 kg Mains supply 90 to 270VAC, 50Hz/60Hz Mains supply fuse 3 Amp ( F3A L250V) Replace only with similar type Power supply rating 3 Amps total including battery charge 28V +/- 2V Maximum ripple voltage ≤200 millivolts Battery type Two 12 Volt sealed lead acid in series. 7Ah maximum Battery charge voltage 27.6VDC nominal Battery charge current 0.7A maximum Current draw in mains fail condition 0.095 Amps With buzzer sounding Current draw in second stage alarm 0.235Amps Two zones in fire(470 ohm in circuit) Current draw in post discharge condition 0.310Amps solenoid outputs active Maximum current draw from batteries 3Amps With main power disconnected NAC outputs(sounder & bell circuit) 26 to 28V DC Fused at 500mA with electronic fuse 1.2Amp total load over all circuits Fault relay contact rating 2A /30VDC maximum for each Volt free changeover contact Fire relay contact rating 2A /30VDC maximum for each Volt free changeover contact First stage contact rating 2A /30VDC maximum for each Volt free changeover contact Second stage contact rating 2A /30VDC maximum for each Volt free changeover contact Extract contact rating 2A /30VDC maximum for each Volt free changeover contact Zone quiescent current 4mA maximum Terminal capacity 0.5mm2 to 2.5mm2 solid or stranded wire Number of detectors per zone ≤30 PCS conventional detectors Number of sounders per circuit Dependent on type and current consumption Detection circuit end of line 4K7±5% 1/2 Watt resistor 3K-5.6K 1/2W Monitored input end of line 4K7±5% 1/2 Watt resistor 3K-5.6K 1/2W Sounder circuit end of line 10K±5% 1/2 Watt resistor 6.8K-20K 1/2W Extinguishant output end of line 10K±5% 1/2 Watt resistor 6.8K-20K 1/2W No. of detection circuits Four 21 to 28V DC No. of sounder circuits Four 21 to 28V DC Extinguishant release output 21V to 28V DC. Maximum load 2 Amp Extinguishant release delay time Adjustable 0 to 75 seconds 5 second steps SIL, AL, FLT, RST inputs Switched – min resistance 0 ohms, max 1k ohms Detector alarm threshold 270 ohms to 1K ohms Call point alarm threshold 150 ohms to 1K ohms Short circuit threshold 0 ohms to 130 ohms Status unit/Ancillary board connection Two wire RS485 connection with electronic fuse. Max. of 32 units-RS485 data cable The controller is connected with Conventional Smoke Detector, heat Detector, Manual call point, on-site emergency start/stop button, aerosol extinguishing control device (or cylinder control device), weighing device, exhaust indicator light and other equipment. Constitute a complete automatic fire alarm and fire fighting system. Download manual and diagram for fire alarm and fire fighting system. Conventional Fire Fighting Panel Key Specifications/Special Features Four Style B（Class B）Initiating Device Circuits（IDCs）。 All zones accept two-wire smoke detectors and any normally-open contact devices. One built-in Fire Fighting Ouput. 24-volt operation. Resettable four-wire smoke detector power＠500 mA. Non-resettable power＠500 mA. One-man walk-test programmable for silent or audible test. Disable/Enable control per IDC. Reverse polarity protection There are 6 buttons on the panel, Emergency evacuation, external muffler, Self-test/Reset, Internal muffler, exhaust fan, Emergency Stop Control lock allows and disables key function, manual and automatic switching modes The standby 12V/4.5A power supply is placed at the bottom of the chassis. If the battery polarity is incorrect, the yellow battery fault message is displayed on the panel. Emergency gas release: Pull out the yellow plastic box panel on the panel, and there is a red button inside. Press the button, the controller will enter the "emergency start" delay state, showing a countdown of 10 seconds, and send a start signal after the countdown is over. L Controller has 4 independent alarm area (ZONE1-ZONE4), can be connected with multi-line smoke, temperature, manual alarm Button and other input equipment, can independently complete equipment fault detection and alarm function. L The controller has three sound and light alarm outputs (SounD1-SOUND3), which can be easily used for external emergency alarm in case of fire . L the controller has one 24VDC/1A POWER output (power-24 v,0V) to supply POWER to external devices. L Controller has 1 way fault, 1 way fire alarm relay output. L The controller has remote mute, remote alarm test, remote fault test and remote reset functions. L The controller has remote emergency start, remote emergency stop and remote hand/automatic mode switching functions. L The controller has cylinder pressure undervoltage signal receiving function and gas release feedback signal receiving function. L The controller has valve function. L The controller can set 0-75s delay valve function. L The controller has the function of manually opening and closing the exhaust fan. L The controller has RS485 interface, which can transmit alarm information with the upper computer or the floor repeat display. 2. Technical indicators Remarks of electrical parameters of the project Working power supply DC12V-DC28V Ripple voltage is 200 mV The static current is 0.12A The alarm current is 0.235A The output current is 24/3a Relay output contact capacity 24V/2A, 220V/1A Acoustic and optical output power of each channel 24V/1A (Max) Static currents in alarm zone (Zone1-4) 0mAminimum, 2mAmaximum A twisted pair cable with a lead of 0.75mm2 to 2.5mm2 is recommended The number of detectors in each alarm zone (ZONE1-4) is 25 Detector, monitor input terminal resistance 6K8±5% 1/2W Acousto-optic alarm output terminal resistance 10K±5% 1/2W Controller alarm area (ZONE1-ZONE4) alarm resistance 1K - 390 Parallel diodes 1N4004 or 1N4007 are recommended for valve output Zone1-zone4: input alarm equipment for multi-wire smoke sensing, temperature sensing, manual alarm button, etc. ZONE1 and ZONE2 participate Linkage "and" control output, ZONE3 and ZONE4 only alarm function, do not participate in linkage control output. It is recommended that ZONE1 be connected to multiple cables - type smoke detector, ZONE2 connected with multi - line temperature detector. When both ZONE1 and ZONE2 alarm, the controller will enter the linkage loss Out (The controller is in automatic state) state Fire alarm and automatic fire control must be installed in communication room, warehouse, factory.

$149.00

Add to Cart

FACP small business fire security equipment

4-zone to 16-zone FACP (Fire Alarm Control Panel), which uses conventional input devices like detectors, pull stations and other normally-open contact devices. Outputs include four Notification Appliance Circuits (NAC, SOUND1-4), three standard Form-A relays (alarm, trouble and supervisory) and an EIA-485 port to interface with remote annunciators and optional remote relay modules. The FACP is field programmable via the panel keypad. It also supervises all wiring, AC voltage and battery level. The working power supply is 24V DC, powered by the main circuit (AC 90–270V) and a backup battery (two 12V/7Ah lead-acid batteries), ensuring continuous operation for at least 8 hours in case of mains power failure. The device supports 4 to 16 independent zones (Zone), each capable of connecting up to 25 conventional smoke detectors, heat detectors, or normally open manual alarm buttons (Pull Station), and can independently display fire alarm, fault, or supervision status for each circuit. The panel features 4 alarm output circuits, enabling linkage with external devices such as audible and visual alarms, fire evacuation broadcasts, elevator descent, and smoke extraction fans. It also includes 3 standard relays for logic control (e.g., delayed activation, interlocking closure, etc.), along with an EIA-485 (RS-485) communication port for data exchange with host computers, building automation systems (BAS), or remote monitoring centers to achieve centralized management. The device has a comprehensive self-check function, monitoring abnormalities such as mains power, backup power, line open circuit, short circuit, or detector offline, and visually displaying them via LED indicators. The control interface includes five physical buttons: Silence, Mute, Test, Reset, and Mode, complying with international fire protection equipment human-machine engineering standards. The housing is made of metal material with an IP54 protection rating, operating temperature range of 10°C to +50°C, and relative humidity not exceeding 95% (no condensation), meeting the stringent requirements of industrial environments. It aligns with international standards such as EN 54 and UL 864 for multi-wire system requirements The fire alarm system instruction and manual can be downloaded at conventional fire alarm Product Features （1）4,8,16 Class B Initiating Device Circuits (IDCs) （2）All zones accept conventional detectors and any normally open contact device （3）Four Class B Notification Appliance Circuits (NACs) （4）One Form-A Alarm Relay （5）One Form-A Trouble Relay （6）One Form-A Supervisory Relay （7）3.0 amps of system power （8）Max 30 conventional detectors in one zone. （9）Auto/Manual mode setting enable walk test. （10）Each Zone can be disabled, （11）Sound output can be disabled. (12) Manual active sound output enabled. (13)Able to report short and broken circuit of detection zones. （14）Designed with standby batteries and space provision for two sealed lead-acid batteries. （15）Testing and disable functions. （16）Can connect max 32 repeater panels by RS485 communication port （17） Dimensions : 14.57" (37 cm) long X 17.32" (44 cm) high X 3.94"(10cm). （18） Weight: 6.6kg (without battery)